Backstage

Day: vampire fangs

How to make vampire teeth

by on Mar.11, 2010, during Special Effects

Here is the backstage for the construction of a denture (it is actually a crown) realism of undisputed, highly effective in making short films, live events, cosplay or just for a change’ their look depending on the mode.

Corona da vampiro

L’ need is available in all stores for dentists or dental, possibly also at a good price online.

Materials needed:

  • An impression tray top of the desired size
  • Alginate per imprint, slow.
  • Gypsum powder.
  • Disposable latex gloves.
  • Dough or put.
  • Vaseline.
  • Resin for provisional.
  • Pre-vulcanized liquid latex
  • Bototalco
  • Silicone Impression (it only takes a small amount)
  • any water-based acrylic colors

Corona da vampiro

The first step is to take an impression of the teeth. This is done using the special tray and a fair mixture of water and alginate (I use Neocolloid, which is also excellent for making the cast of the face or any part of the body).

Once the slurry has been stabilized and hardened (by 3 to 5 minutes) you can clean the mouth and fill with a mixture of water and gypsum. Council to do this in two stages: the first with a very liquid mixture that is stratified throughout the footprint, It need operation during which tap the table, is to remove small air bubbles present, that in order to enable the plaster to make every detail present on the mold.

The second, every few minutes from the first, a little more dense, as a filler.

After a period ranging from 20 minutes 2 hours, depending on the plaster you have chosen, Your positive is ready.

If you have a latex liquid, I recommend using it to coat the stamp with a light film, Dab with talcum powder: This will make it much easier to loose the prosthesis as well as give a slight 'game’ made to the crown, that make it more comfortable and durable.

On the positive thus created and covered by a layer of latex, it is now possible to model your new teeth with the plasticine or clay.

After work cover everything with a thin layer of vaseline, that, as well as allow the posting of the counter that we will achieve, is also useful to give a good polish to the whole tooth.

Corona da vampiro

The prototype so grossed must be placed in the freezer for a couple of hours, so that the plasticine or clay to take a good consistency.

After such an interval may be made to make the mold with key (that is, with a detail, such as a small pin located on the palate) allowing for the repositioning of the same counter.

To accomplish the latter you can use different types of materials, but I have experimentally verified that the best is the silicone impression (Flexitime EasyPutty), that breaks away from the plaster once catalyzed, is flexible and allows slight undercuts, separating the resin and is reusable !

Wait until the counter that you cast or molded on the model is hard, and disconnect it from your work again. Make sure that the work done so far has managed well and remove the dough from the positive (and if present in trace, also from the negative).

Now comes the most delicate moment, the realization of the real prosthesis molding.

Given the nature of the used substances near, I suggest you work in a well ventilated place and using latex gloves.

Liquid and powder (I used a medium color Duralay clear) be blended in appropriate quantities (about 1:1) and then poured into the mold, closed immediately with good positioning with the key you created earlier. Obviously a soft mold will make it much easier being removed.

Corona da vampiro

After a variable time between half an hour and 2 hours depending on the resin used can be removed to cut the crown, remove small imperfections, lucidarla, and colored end.

In some of the attached pictures you can see how he left a large area of coverage on the gums. This is not always necessary, rather, often the most realistic prosthesis cover only the teeth. A skilful use of color and a couple of coats of clear gloss will give your life to finally sighed work.


Calco in gesso

Modello in plastilina

Controstampo in silicone

Plaster cast

Model in clay

Controstampo in silicone

Modello stampato

Modello rifinito

Modello rifinito

Prosthetics printed

Finished prosthesis

Prosthetics colored
21 Comments :, , , , , , , , , , , , , , , , , , , , more...

Looking for something specific ?

Use the box below to conduct your searches:

Nothing yet? Leave a comment on a page, or contact us so we'll take care of it!